Azionamenti Passo Passo - Pibot stepper motor driver rev.2.3

Pibot stepper motor driver rev.2.3
Azionamenti Passo Passo - Pibot stepper motor driver rev.2.3
14,64€
Imponibile: 12,00€
  • Magazzino: Disponibile
  • Marchio: Pibot
  • Modello: 00002486
  • Peso: 0.07kg

Piccolo azionamento passo passo che si puo' usare con Mach3 USBCNC Raspberry e molto altro.

  • Quick connector and Normal connector suitable for hobby and factory.

  • Wide power input DC 8 - 40V.

  • Signal supply logic in Quick connector (en dir clk "3.3V or 5V") optical isolated to the IC.

  • Signal supply logic in Normal connector (en dir clk dgnd "2V to 6V logic") with high speed direct to IC.

  • Microstepping: 1/1, 1/2A, 1/2B, 1/4, 1/8, 1/16(default).

  • 0 - 4.5A(4.12A) ~ (from Toshiba6600 manual) output current can be accurate set by read the voltage of voltmeter.

  • Diagnosis LED available.

  • Heatsink available.

  • Reserve the M3 M2 M1 TQ input pins for program control.

 

How it works

Input and Output

Normal connector and Quick connector is parallel. ONLY ONE CONNECTOR REQUIRED AT ONE TIME.

input-and-output

 

Micro-stepping Setting

This picture shows how you can change the micro-stepping settings of the driver.

mirco-stepping-setting

 

Output Limit current Adjust

You can approximate the current limit by the position of the marked point on the trimmer. DO NOT EXCEED YOUR MOTOR'S CURRENT RATING.

OR the current limit can be adjusted by measuring VREF and turning the trimmer. Connect the [+] of the voltmeter to VREF and the [-] lead to GND and read the value.

Current Limit = VREF ÷ 0.6801

So for example the Max current is: 2.81V ÷ 0.6801 = 4.1317A

output-limit-current-adjust

 

Connect with PiBot Kits

http://www.pibot.com/ben/tutorials-connect-your-hardware-2-x/stepper-driver-and-motor-connect.jpg

 

http://www.pibot.com/ben/tutorials-connect-your-hardware-2-x/multiple-quick-connector.jpg

 

Documents

 

Specification

  • Driver Chip: Toshiba

 

Scrivi una recensione

Nota: Il codice HTML non viene tradotto!
Punteggio:
Negativo Positivo
Captcha
Acquisti Sicuri
Spedizione VEloce
Facilità Reso
Servizion 24h
Motore passo passo Nema 23 flangia 56 1,1 Nm 2,2 A. SANYO DENKY..
39,04€
Imponibile:32,00€
Acquista
0,45 Nm, Nema 17.  ..
31,72€
Imponibile:26,00€
Acquista
What is it Display Controller with 4 keys, LCD-2004 and a TF card reader, Used for display the Printer status and Print by the TF Card. Di..
19,52€
Imponibile:16,00€
Acquista
What is it Designed for GRBL CNC and 3D printer. link between your PC and your stepper driver drivers for stepper motors. It uses the USB por..
85,40€
Imponibile:70,00€
Acquista
What is it This is a simple way to add a relay to your micro controller or CNC controller. It runs off 5V or 3.3V and most controllers can easily ..
9,76€
Imponibile:8,00€
Acquista
Motore passo passo P42-2H-1-A-040-4
Novità
0,24 Nm, 0,4 Amper, Nema 17  ..
18,30€
Imponibile:15,00€
Acquista
Motore Passo Passo 42J1860-417
Novità
0,85 Nm, 1,7 Amper, Nema 17  ..
21,96€
Imponibile:18,00€
Acquista
Motore Passo Passo 42J1848-425
Novità
0,5 Nm, 2,5 Amper, Nema 17  ..
20,74€
Imponibile:17,00€
Acquista